1. Warranty Claim
You can find the serial number on the rear panel of
this unit. In case of warranty claim, please report this
From time to time you should wipe the front and
rear panels and the cabinet with a soft cloth. For
heavier dirt, dampen a soft cloth in a weak solution
of mild detergent and water, wring it out dry, and
wipe off the dirt. Following this, dry immediately with
a clean cloth. Do not use rough material, thinners,
alcohol or other chemical solvents or cloths since
these could damage the finish or remove the panel
BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME,
READ THE FOLLOWING SECTION CAREFULLY.
The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit will
be used meets the required voltage (e.g., AC 230 V,
50 Hz or AC 120 V, 60 Hz) written on the rear panel.
Setting the STANDBY button to standby does not
shut off the power completely. So the power cord
should be removed from the AC outlet when the
unit is not used for a prolonged time.
For British model
Replacement and mounting of an AC plug on the
power supply cord of this unit should be performed
only by qualified service personnel.
The wires in the mains lead are coloured in
accordance with the following code:
Brown : Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured blue must be connected
to the terminal which is marked with the letter N or
The wire which is coloured brown must be
connected to the terminal which is marked with the
letter L or coloured red.
A 5 ampere fuse is fitted in this plug. Should the fuse
need to be replaced, please ensure that the
replacement fuse has a rating of 5 amperes and that it
is approved by ASTA or BSI to BS1362. Check for the
ASTA mark or the BSI mark on the body of the fuse.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR
THE SOCKET OUTLET IN YOUR HOME THEN THE
FUSE SHOULD BE REMOVED AND THE PLUG CUT
OFF AND DISPOSED OF SAFELY. THERE IS A DANGER
OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF
PLUG IS INSERTED INTO ANY 13 AMPERE SOCKET.
If in any doubt, please consult a qualified electrician.
For U.S. model
Note to CATV system installer:
This reminder is provided to call the CATV system
installer's attention to Article 820-40 of the NEC,
ANSI/NFPA 70, which provides guidelines for proper
grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system
of the building, as close to the point of cable entry
FCC Information for User
The user changes or modifications not expressly
approved by the party responsible for compliance
could void the user's authority to operate the
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment
· Connect the equipment into an outlet on a circuit
different from that to which the receiver is
· Consult the dealer or an experienced radio/TV
technician for help.
For Canadian model
For models having a power cord with a polarized
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Modele pour les Canadien
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE
ET POUSSER JUSQU'AU FOND.