MITSUBISHI DD6000 Service Manual

Cover page of MITSUBISHI DD6000 Service Manual

Service Manual for MITSUBISHI DD6000, downloadable as a PDF file.

Manual details

  • Immediate download after payment.
  • Delivered as a PDF file.
  • The manual has 71 pages
  • File size: 7.82 MB
  • Available language versions: English
  • Different language versions may vary sligthly in file size and page count.

We guarantee that...

  • our manuals are complete,
  • the manual includes circuit diagrams,
  • our manuals are checked with antivirus,
  • We'll issue refund if the manual is damaged, incomplete or unreadable (our refund policy)

Sample pages

Thumbnail of page 1Thumbnail of page 2Thumbnail of page 3Thumbnail of page 4
Thumbnail of page 5Thumbnail of page 6Thumbnail of page 7Thumbnail of page 8
Thumbnail of page 9
background image
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Rd. Irvine, CA 92618
Copyright © 2000 Mitsubishi Digital Electronics America, Inc.
All Rights Reserved
Operating conditions:
Temperature: 5°C to 35°C
Operation status:
Horizontal
Video output:
1.0 V (p-p), 75
, negative
sync., pin jack x 1
S Video output:
(Y) 1.0 V (p-p), 75
, nega-
tive sync., Mini DIN 4-pin x 1
(C) 0.286 V (p-p), 75
Color Difference outputs: (Y) 1.0 V (p-p), 75
,
(1 Interlaced)
negative sync., pin jack x 1
(1 Progressive)
(Cr, Pr)/(Cb, Pb) 0.7 V (p-p),
75
, pin jack x 2
Digital Audio output:
(Bitstream/PCM) 0.5 V (p-p),
75
, pin jack x 1,
Optical connector x 1
Analog Audio output:
2.0 V (rms), 220
, pin jack
2 CH L R x 2,
5.1 CH SURROUND x 6
CAUTION
Before servicing this chassis, it is important that the service person reads all SAFETY PRECAUTIONS and the
SAFETY NOTICE in this manual.
SPECIFICATIONS
Power Supply:
120V AC, 60 Hz
Power Consumption:
19W
Weight:
6.8 lb.
External Dimensions:
17"x 3-1/4"x12-1/4"
(W/H/D)
Signal System:
Standard NTSC
Laser:
Semiconductor laser,
wavelength 650 nm
Frequency Range:
(Digital Audio)
Audio CD:
4 Hz to 20 kHz
DVD Linear -
48 kHZ Sampling: 4 Hz to 22 kHz
96 kHZ Sampling: 4 Hz to 44 kHz
Signal-To-Noise Ratio:
More than 112 dB (EIAJ)
Audio Dynamic Range: More than 106 dB (EIAJ)
Harmonic Distortion:
Less than 0.001%
Wow and flutter:
Below measurable level
(less than ± 0.001%
(W.PEAK)) (EIAJ)
Service
Manual
2000
MITSUBISHELECTRIC
Model
DD-6000
DVD Player
OPEN/CLOSE
STOP
PLAY
PAUSE/STEP
POWER
DD-6000
STANDBY
SKIP
REV
FWD
/
CDVD
TITLETRK CHP
TOTAL REMAIN
MEMORY
HDCD
This service manual contains the differences between models DD-5000 and DD-6000.
It also includes information for the DD-6000 that is identical to the DD-5000.
background image
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Rd. Irvine, CA 92618
Copyright © 2000 Mitsubishi Digital Electronics America, Inc.
All Rights Reserved
Operating conditions:
Temperature: 5°C to 35°C
Operation status:
Horizontal
Video output:
1.0 V (p-p), 75
, negative
sync., pin jack x 1
S Video output:
(Y) 1.0 V (p-p), 75
, nega-
tive sync., Mini DIN 4-pin x 1
(C) 0.286 V (p-p), 75
Color Difference outputs: (Y) 1.0 V (p-p), 75
,
(1 Interlaced)
negative sync., pin jack x 1
(1 Progressive)
(Cr, Pr)/(Cb, Pb) 0.7 V (p-p),
75
, pin jack x 2
Digital Audio output:
(Bitstream/PCM) 0.5 V (p-p),
75
, pin jack x 1,
Optical connector x 1
Analog Audio output:
2.0 V (rms), 220
, pin jack
2 CH L R x 2,
5.1 CH SURROUND x 6
CAUTION
Before servicing this chassis, it is important that the service person reads all SAFETY PRECAUTIONS and the
SAFETY NOTICE in this manual.
SPECIFICATIONS
Power Supply:
120V AC, 60 Hz
Power Consumption:
19W
Weight:
6.8 lb.
External Dimensions:
17"x 3-1/4"x12-1/4"
(W/H/D)
Signal System:
Standard NTSC
Laser:
Semiconductor laser,
wavelength 650 nm
Frequency Range:
(Digital Audio)
Audio CD:
4 Hz to 20 kHz
DVD Linear -
48 kHZ Sampling: 4 Hz to 22 kHz
96 kHZ Sampling: 4 Hz to 44 kHz
Signal-To-Noise Ratio:
More than 112 dB (EIAJ)
Audio Dynamic Range: More than 106 dB (EIAJ)
Harmonic Distortion:
Less than 0.001%
Wow and flutter:
Below measurable level
(less than ± 0.001%
(W.PEAK)) (EIAJ)
Service
Manual
2000
MITSUBISHELECTRIC
Model
DD-6000
DVD Player
OPEN/CLOSE
STOP
PLAY
PAUSE/STEP
POWER
DD-6000
STANDBY
SKIP
REV
FWD
/
CDVD
TITLETRK CHP
TOTAL REMAIN
MEMORY
HDCD
This service manual contains the differences between models DD-5000 and DD-6000.
It also includes information for the DD-6000 that is identical to the DD-5000.
background image
SAFETY PRECAUTIONS
LEAKAGE CURRENT CHECK
Plug the AC line cord directly into a 120V AC outlet (do
not use an isolation transformer for this check). Use an
AC voltmeter, having 5000
per volt or more sensitivity.
Connect a 1500
10 W resistor, paralleled by a 0.15 µF
150V AC capacitor between a known good earth ground
(water pipe, conduit, etc.) and all exposed metal parts of
the cabinet (antennas, handle bracket, metal cabinet
screwheads, metal overlays, control shafts, etc.).
Measure the AC voltage across the 1500
resistor.
The test must be conducted with the AC switch on and
then repeated with the AC switch off. The AC voltage
indicated by the meter may not exceed 0.3 V. A reading
exceeding 0.3 V indicates that a dangerous potential
exists, the fault must be located and corrected.
Repeat the above test with the DVD VIDEO PLAYER
power plug reversed.
NEVER RETURN A DVD VIDEO PLAYER TO THE
CUSTOMER WITHOUT TAKING NECESSARY
CORRECTIVE ACTION.
READING SHOULD NOT EXCEED 0.3V
DVD VIDEO PLAYER
AC VOLTMETER
(5000
9 per volt
or more sensitivity)
Good earth ground
such as a water pipe,
conduit, etc.
1500
9
10 W
0.15
µF 150V AC
AC OUTLET
Test all exposed metal.
Voltmeter Hook-up for Leakage Current Check
background image
LASER BEAM CAUTION LABEL
When the power supply is on, do not remove this laser caution label. If it is removed, laser radiation may be recceived.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
SAFETY NOTICE
background image
SECTION 2
PART REPLACEMENT AND ADJUSTMENT PROCEDURES
SECTION 3
SERVICING DIAGRAMS
1 . CIRCUIT SYMBOLS AND
SUPPLEMENTARY EXPLANATION
1-1. Precautions for Part Replacement
1-2. Solid Resistor Indication
1-3. Capacitance Indication
1-4. Inductor Indication
1-5. Waveform and Voltage Measurement
1-6. Others
1-7. When Replaced ROM ICs or Upgraded Firmwareo
2 . PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM
3 . BLOCK DIAGRAMS
3-1. Overall Block Diagram
3-2. Main Block Diagram
3-2-1. Logical System Block Diagram
3-3. Output Block Diagram
4 . CIRCUIT DIAGRAMS
4-1. Output Circuit Diagram
4-2. Sub Video Circuit Diagram
CONTENTS
SECTION 1
GENERAL DESCRIPTIONS
SECTION 4
PARTS LIST
SAFETY PRECAUTION
NOTICE
ABBREVIATIONS
1. Integrated Circuit (IC)
2. Capacitor (Cap)
3. Resistor (Res)
4 . EXPLODED VIEWS
4-1. Packing Assembly
4-2. Chassis Assembly
4-3. Mechanism Assembly
5. PARTS LIST
General descriptions such as preparation for servicing, location of mechanical parts and troubleshooting are the same as
model DD-5000.
The pages from model DD-5000, Section 1, are included in this text.
Part replacement and adjustment procedures are the same as DD-5000.
The pages from model DD-5000, Section 2, are included in this text.
background image

Reviews

There are no reviews of this manual yet.